Zephyrproject Zephyr vulnerabilities
295 vulnerabilities
Known vulnerabilities in Zephyrproject Zephyr, newest first, with CVSS severity, EPSS, KEV listings, ransomware use and the affected versions.
CVE-2026-75085zephyrprojectzephyr
EPSS score0.21%
The STM32WBA IEEE 802.15.4 driver in drivers/ieee802154/ieee802154_stm32wba.c computed the packet length of a received frame as pkt_len = rx_frame->length - IEEE802154_FCS_LENGTH without first checking that the radio-reported length could hold an FCS. pkt_len is a uint8_t, so a reported length of 0 or 1 wrapped to 254 or 255. The only bound on the resulting value was __ASSERT_NO_MSG(pkt_len <= CONFIG_NET_BUF_DATA_SIZE), which compiles to nothing in the default production configuration (CONFIG_ASSERT=n).
The length originates in the ST link-layer receive-done metadata (p_metadata->length, stored by stm32wba_802154_receive_done()), and ultimately in the PHY header of a frame received over the air, so it is influenced by any attacker within radio range of the device. Reaching the underflow requires the vendor link layer to surface a frame shorter than the FCS with no error; the driver performed no validation of its own on that value.
When the underflow occurs, stm32wba_802154_rx_thread() calls net_pkt_write(pkt, rx_frame->psdu, pkt_len) with a length of about 254 bytes against a receive buffer that holds at most one PHY packet (IEEE802154_MAX_PHY_PACKET_SIZE, 127 bytes). This reads roughly 128 bytes past the end of the radio receive buffer and copies that adjacent memory into a network packet that is submitted to the networking stack, giving an out-of-bounds read with a potential disclosure of adjacent RAM plus needless oversized packet allocation in the RX thread.
The fix rejects a frame whose reported length is smaller than IEEE802154_FCS_LENGTH before the subtraction, and replaces the compiled-out assertion with a runtime length check that drops oversized frames — matching the runtime check already present in drivers/ieee802154/ieee802154_nrf5.c.CVE-2026-75084zephyrprojectzephyrEPSS score0.29%
The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio's RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len < 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped.
An unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip's 128-byte RX FIFO has not overflowed, so the driver's RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required.
With the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment's buf->data and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected.CVE-2026-75083zephyrprojectzephyrEPSS score0.23%
The receive path of the NXP KW41Z IEEE 802.15.4 driver, kw41z_rx() in drivers/ieee802154/ieee802154_kw41z.c, computed the payload size as pkt_len = len - KW41Z_FCS_LENGTH in a uint8_t, where len is the frame length reported by the radio. The interrupt handler kw41z_isr() obtained that length from the RX_FRAME_LENGTH field of the ZLL IRQSTS register — a copy of the PHY header length byte of the frame received over the air — and only rejected the value zero. A reported length of one therefore underflowed to pkt_len == 255.
Because the packet is allocated with NET_AF_UNSPEC on a non-Ethernet L2, net_pkt_rx_alloc_with_buffer() does not clamp the request to the interface MTU; with the default fixed-size buffer pool (CONFIG_NET_BUF_FIXED_DATA_SIZE, CONFIG_NET_BUF_DATA_SIZE=128) the allocation succeeded as a chain of two fragments. The subsequent register-to-buffer copy loops write into the first fragment only, so 255 bytes were written into a 128-byte net_buf data block, overrunning it by up to 127 bytes into adjacent network-buffer-pool memory, and reading up to 128 bytes past the end of the radio's PKT_BUFFER_RX register array.
The length field originates from an unauthenticated frame transmitted by any device within 802.15.4 radio range, and is captured by the hardware at PHY-header time — before frame filtering has completed — while the handler samples it after clearing the interrupt status, so an attacker flooding frames with a length byte of one can drive the underflow. The impact is memory corruption in the shared receive buffer pool from interrupt context, most plausibly a crash or corruption of other packets' data; the overflowing bytes are radio register contents rather than attacker-authored data, which bounds the integrity impact.
The fix rejects any length below KW41Z_FCS_LENGTH and additionally verifies net_buf_tailroom() of the first fragment before the copy loops, which also covers the CONFIG_NET_L2_OPENTHREAD variant of the size computation.CVE-2026-19673zephyrprojectzephyrEPSS score0.34%
ethernet_recv() in subsys/net/l2/ethernet/ethernet.c validates only that the first net_buf of a received frame holds a plain 14-byte struct net_eth_hdr. When the ethertype is 0x8100 and VLAN is enabled on the interface, the same buffer is reinterpreted as the 18-byte struct net_eth_vlan_hdr without re-checking the length: the VLAN TCI and the inner ethertype are read from offsets 14..17, past pkt->buffer->len, and hdr_len is raised to 18 so the subsequent net_buf_pull() removes more bytes than the buffer holds.
A single unauthenticated frame of 14 to 17 bytes carrying the VLAN ethertype triggers this. No knowledge of the node's VLAN configuration is needed: net_eth_get_vlan_iface() returns the base interface for the priority tag 0, and a broadcast destination address satisfies the "frame is for me" test, so a 16-byte broadcast frame with ethertype 0x8100 and TCI 0x0000 reaches the pull. Nothing in the receive path enforces the 60-byte Ethernet minimum — the USB CDC ECM and CDC NCM gadget classes in particular hand host-supplied frames of any non-zero length straight to net_recv_data().
With assertions enabled, net_buf_simple_pull() asserts and the node panics. In a production build (assertions and CONFIG_NET_BUF_HARDENING off) the uint16_t buffer length underflows to 65534 and buf->data is advanced past the end of the fragment's storage, so every later parser reads far outside the buffer and any net_buf_add() on that fragment computes tailroom from the underflowed length. The result is a reliable remote denial of service and out-of-bounds access with information-disclosure and corruption potential.
Only configurations built with CONFIG_NET_VLAN=y that have a VLAN enabled on the receiving Ethernet interface, and whose MAC does not strip VLAN tags in hardware (ETHERNET_HW_VLAN_TAG_STRIP), are affected. The fix rejects the frame before the tag is read, so hdr_len is thereafter either 14 or 18 with both sizes validated against pkt->buffer->len.CVE-2026-19940zephyrprojectzephyrEPSS score0.19%
The Bluetooth Classic Hands-Free Profile Audio Gateway implementation in subsys/bluetooth/host/classic/hfp_ag.c keeps its struct bt_hfp_ag objects in a static pool indexed by ACL connection index. On link teardown, hfp_ag_disconnected() cancels ag->tx_work and the per-call work items and then clears ag->acl_conn, which marks the pool slot as free — but it leaves ag->ongoing_call_work (and ag->slc_work) untouched. The next connection that lands on the same slot enters hfp_ag_create(), whose only occupancy test is ag->acl_conn, and immediately executes memset(ag, 0, sizeof(struct bt_hfp_ag)) followed by k_work_init_delayable(). Zeroing and re-initialising a k_work_delayable whose struct _timeout node is still linked into the kernel timeout list leaves the kernel holding a reference to a node with NULL prev/next links.
ag->ongoing_call_work is armed by the remote peer: when a Hands-Free unit sends AT+CIND? during Service Level Connection establishment and the application provides the asynchronous get_ongoing_call callback, the AG schedules the work for CONFIG_BT_HFP_AG_GET_ONGOING_CALL_TIMEOUT milliseconds (default 10000). The timer is cancelled only if the application answers in time via bt_hfp_ag_ongoing_calls(). A peer that sends AT+CIND?, then disconnects the HFP RFCOMM DLC, then immediately re-opens it on the same ACL link, reuses the same pool slot deterministically while the timeout is still pending — the AG's RFCOMM server accept path (hfp_ag_accept()) calls hfp_ag_create() directly, so the remote side drives both teardown and re-creation.
The result is corruption of the kernel's timeout list: sys_dlist_remove() on the zeroed node performs writes through NULL pointers from the clock-announce path, and rescheduling the re-initialised work re-inserts a node the list already references, creating a cycle that the announce loop walks with interrupts locked. The observable impact is a fault or hang of the whole system, i.e. a denial of service reachable from Bluetooth radio range; no attacker-controlled data is written, so this does not by itself yield code execution. Exposure is limited to builds with CONFIG_BT_HFP_AG (marked experimental and disabled by default) whose application implements the asynchronous get_ongoing_call callback.CVE-2026-19939zephyrprojectzephyrEPSS score0.18%
The AVDTP signalling layer arms a 6-second command timeout (AVDTP_TIMEOUT) in avdtp_send_cmd() whenever the local device issues an AVDTP request. Every response handler in subsys/bluetooth/host/classic/avdtp.c cancels session->timeout_work before clearing the pending request, but bt_avdtp_l2cap_disconnected() only cleared session->req and left the delayable work armed. The struct bt_avdtp session is the first member of struct bt_a2dp, whose instances live in a static per-connection array, and a2dp_get_connection() in subsys/bluetooth/host/classic/a2dp.c wipes a slot with memset() as soon as session->br_chan.chan.conn is NULL — which the L2CAP layer arranges immediately after the disconnect callback returns.
A remote Bluetooth BR/EDR peer triggers the condition by opening the AVDTP signalling channel, letting the local application issue an AVDTP procedure (the standard A2DP flow issues bt_a2dp_discover() from the connected callback), then tearing the signalling channel down without responding and re-opening it within the remaining timeout window. The reconnect reaches a2dp_accept() → a2dp_get_connection(), which zeroes the whole struct bt_a2dp while the work item's struct _timeout is still linked into the kernel's global timeout list. Both the disconnect and the reconnect instants are chosen by the attacker, so no race has to be won; an encrypted BR/EDR link is required, and CONFIG_BT_A2DP (experimental) must be enabled.
With the default CONFIG_TIMEOUT_BACKEND_DLIST backend the kernel decides a timeout is inactive by testing whether its list node is linked, so after the memset() the kernel treats a node that is still on the global timeout list as free: the announce path pops a node whose links and handler pointer are NULL, and the next bt_work_reschedule() on the recycled session re-inserts the same node into a list that already contains it. The consequence is corruption of the single kernel data structure every timer, timeslice and sleep depends on — writes through zeroed or stale list pointers and a NULL handler dispatch — producing a system-wide crash or hang rather than a fault confined to the A2DP session.
The fix cancels session->timeout_work at the top of bt_avdtp_l2cap_disconnected() and moves k_work_init_delayable() from avdtp_send_cmd() to the session-establishment paths bt_avdtp_connect() and bt_avdtp_l2cap_accept(), so the work item is always initialized before a disconnect callback can run.CVE-2026-19937zephyrprojectzephyrEPSS score0.18%
The Bluetooth Mesh Access layer delayable-message machinery in subsys/bluetooth/mesh/delayable_msg.c manages a static pool of CONFIG_BT_MESH_ACCESS_DELAYABLE_MSG_COUNT message contexts (default 4) threaded onto a free_ctx or busy_ctx list. release_delayable_msg_ctx() returned a context to free_ctx only when sys_slist_find_and_remove() found it on busy_ctx. The chunk-exhaustion error path in bt_mesh_delayable_msg_manage() releases a context that was already popped off free_ctx but not yet inserted on busy_ctx, so the context was appended to neither list and was permanently lost from the pool. Because bt_mesh_delayable_msg_init() runs only once from bt_mesh_init(), and node reset/suspend only drain busy_ctx, the loss survives unprovision, re-provision and suspend/resume — it is cleared only by a reboot.
The error path is reached when the chunk pool (CONFIG_BT_MESH_ACCESS_DELAYABLE_MSG_CHUNK_COUNT, default 40 chunks) is short of the chunks a new delayed message needs and the oldest pending message cannot be flushed because bt_mesh_access_send() returns -EBUSY or -ENOBUFS (all segmented-TX contexts busy, or advertising/segment buffers exhausted). A peer that is provisioned into the mesh network — holding a valid NetKey plus an AppKey or DevKey bound to a server model — can drive both conditions by flooding the victim with requests that elicit segmented responses while withholding the Segment Acknowledgment, which keeps the transmit contexts occupied while queued responses hold the chunk pool. Each further request that arrives in that window leaks one context.
Once the pool is drained, bt_mesh_delayable_msg_manage() returns -ENOMEM for every subsequent send and bt_mesh_model_send() propagates that error with no fallback to an immediate transmit. Since CONFIG_BT_MESH_ACCESS_DELAYABLE_MSG and CONFIG_BT_MESH_ACCESS_DELAYABLE_MSG_CTX_ENABLED are both enabled by default, ctx->rnd_delay is set for every received access message, so all replies from Configuration Server, Health Server and application server models are silently dropped. The node keeps receiving and processing traffic but never answers, a persistent denial of service until the device is restarted. There is no memory corruption, information disclosure or integrity impact; releases before the fix compute the chunk count from the transmit buffer capacity rather than its payload length, making chunk-pool starvation — and therefore the leak — considerably easier to provoke.CVE-2026-19938zephyrprojectzephyrEPSS score0.16%
The Bluetooth host's ATT transmit path releases a buffer it does not own when signing fails. chan_send() in subsys/bluetooth/host/att.c documents (and every other error exit implements) the contract that on failure the caller retains ownership of the net_buf; the BT_ATT_OP_SIGNED_WRITE_CMD branch instead called net_buf_unref(buf) when bt_smp_sign() returned an error and then returned that error to the caller. The callers act on the contract: process_queue() re-queues the buffer with k_queue_prepend(), bt_att_chan_send_rsp() puts it back on chan->tx_queue, bt_att_chan_req_send() restores it into the request, and att_req_retry() unreferences it — so the already-freed buffer was re-queued, later dereferenced, and eventually freed again.
An ATT Signed Write Command is produced when an application calls bt_gatt_write_without_response_cb() with sign set on an unencrypted connection. bt_smp_sign() fails whenever no local CSRK exists for the peer (-ENOENT), and whether one exists is negotiated with the peer: smp_distribute_keys() stores a local CSRK only when the peer's pairing key-distribution field requests the signing key and bonding was agreed. A peer can therefore pair without accepting the CSRK, pair with No Bonding, remain unpaired, or keep the link unencrypted, and the victim's next signed write takes the failing path. Because struct net_buf's node field is simultaneously the linkage word for the ATT TX FIFO, for the deferred-destroy list used by the att_pool destroy callback att_tx_destroy(), and for the pool free list, the mishandled buffer corrupts these lists and can be re-issued by bt_att_create_pdu() to a new PDU while the ATT TX path still holds it.
The same branch also saved the net_buf_simple_state only after signing, so a buffer restored after a bt_l2cap_send_pdu() failure kept its 12-octet signature; a subsequent retry re-signed it and appended a second signature with net_buf_add(buf, 12) to a buffer that bt_att_create_pdu() sized for exactly one, writing past the end of the pooled buffer in builds where the net_buf tailroom assertion is compiled out.
Impact is host-side memory corruption in the Bluetooth stack: list corruption, a pooled ATT buffer with two owners (wrong PDU contents transmitted, or a double free when the queues are drained at disconnect), and a bounded out-of-bounds write on the retry path — typically observed as a crash or assertion failure. Exposure requires the deprecated CONFIG_BT_SIGNING to be enabled and an application that actually issues signed writes; in that configuration the triggering condition is under the remote peer's control.CVE-2026-19936zephyrprojectzephyrEPSS score0.14%
The Bluetooth Mesh Access-layer delayable message queue in subsys/bluetooth/mesh/delayable_msg.c shares three intrusive lists (busy_ctx, free_ctx, free_chunks) and one k_work_delayable between two cooperative threads with no synchronization: bt_mesh_delayable_msg_manage() runs on the Bluetooth host RX thread, while delayable_msg_handler() runs on the system workqueue. Both block while the lists are in an intermediate state — the enqueuer in bt_rand(), both in bt_mesh_access_send() — which lets the other context observe torn state. delayable_msg_handler() used the result of sys_slist_get() on busy_ctx without a NULL check, and allocate_delayable_msg_ctx() tested sys_slist_is_empty() and then assumed a separate sys_slist_get() would succeed.
Because CONFIG_BT_MESH_ACCESS_DELAYABLE_MSG and CONFIG_BT_MESH_ACCESS_DELAYABLE_MSG_CTX_ENABLED default to y, every model response to a received mesh message is parked on this queue, so the enqueuer runs as a direct consequence of inbound traffic. A peer that can get access-layer messages accepted by a model (it must hold the NetKey and a bound AppKey, so a legitimate or compromised network member) controls the arrival rate, the size of the elicited responses and the destination address, and thereby controls occupancy of the 4-entry context pool and the 40-entry chunk pool. Exhausting the chunk pool forces bt_mesh_delayable_msg_manage() down the purge path, which sends and releases the only queued message and leaves busy_ctx empty while the delayable work item is still armed; if the enqueuer then yields, the handler runs against the empty list.
The result is a read-modify-write through a NULL-based pointer (pending_msg->fired_time += 10) at a fixed low address on the system workqueue thread. On typical targets that faults, aborting the system workqueue thread — which stops all workqueue-driven functionality, including the mesh timing machinery — or resetting the node, so the impact is loss of availability of the affected node. The write value and address are fixed and no attacker-controlled length or index is involved, so this is not exploitable for memory corruption or code execution. The same unsynchronized window also allowed one message context to be selected and released by two contexts at once, producing duplicated transmissions, duplicated send-completion callbacks and crossed chunk ownership.
The fix serializes every list mutation with a k_spinlock that is never held across a blocking call, makes push_msg_from_delayable_msgs() detach the queue head atomically so a message being sent is on no list, removes the unchecked sys_slist_get() from delayable_msg_handler(), and drops any message that reaches the front of the queue while the stack is suspended or reset.CVE-2018-1000800zephyrprojectzephyrEPSS score1.66%
zephyr-rtos version 1.12.0 contains a NULL base pointer reference vulnerability in sys_ring_buf_put(), sys_ring_buf_get() that can result in CPU Page Fault (error code 0x00000010). This attack appear to be exploitable via a malicious application call the vulnerable kernel APIs (system sys_ring_buf_get() and sys_ring_buf_put).CVE-2021-3322zephyrproject-rtoszephyr+1EPSS score0.54%
Unexpected Pointer Aliasing in IEEE 802154 Fragment Reassembly in Zephyr. Zephyr versions >= >=2.4.0 contain NULL Pointer Dereference (CWE-476). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-p86r-gc4r-4mq3CVE-2021-3510zephyrproject-rtoszephyr+1EPSS score0.96%
Zephyr JSON decoder incorrectly decodes array of array. Zephyr versions >= >1.14.0, >= >2.5.0 contain Attempt to Access Child of a Non-structure Pointer (CWE-588). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-289f-7mw3-2qf4CVE-2021-3436zephyrproject-rtoszephyr+1EPSS score0.98%
BT: Possible to overwrite an existing bond during keys distribution phase when the identity address of the bond is known. Zephyr versions >= 1.14.2, >= 2.4.0, >= 2.5.0 contain Use of Multiple Resources with Duplicate Identifier (CWE-694). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-j76f-35mc-4h63CVE-2021-3433zephyrproject-rtoszephyr+1EPSS score0.20%
Invalid channel map in CONNECT_IND results to Deadlock. Zephyr versions >= v2.5.0 Improper Check or Handling of Exceptional Conditions (CWE-703). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-3c2f-w4v6-qxrpCVE-2021-3435zephyrproject-rtoszephyr+1EPSS score0.21%
Information leakage in le_ecred_conn_req(). Zephyr versions >= v2.4.0 Use of Uninitialized Resource (CWE-908). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-xhg3-gvj6-4rqhCVE-2021-3323zephyrproject-rtoszephyr+1EPSS score0.92%
Integer Underflow in 6LoWPAN IPHC Header Uncompression in Zephyr. Zephyr versions >= >=2.4.0 contain Integer Underflow (Wrap or Wraparound) (CWE-191). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-89j6-qpxf-pfpcCVE-2021-3330zephyrproject-rtoszephyr+1EPSS score0.61%
RCE/DOS: Linked-list corruption leading to large out-of-bounds write while sorting for forged fragment list in Zephyr. Zephyr versions >= >=2.4.0 contain Out-of-bounds Write (CWE-787). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-fj4r-373f-9456CVE-2021-3432zephyrproject-rtoszephyr+1EPSS score0.89%
Invalid interval in CONNECT_IND leads to Division by Zero. Zephyr versions >= v1.14.0 Divide By Zero (CWE-369). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-7364-p4wc-8mj4CVE-2021-3625zephyrproject-rtoszephyr+1EPSS score2.31%
Buffer overflow in Zephyr USB DFU DNLOAD. Zephyr versions >= v2.5.0 contain Heap-based Buffer Overflow (CWE-122). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-c3gr-hgvr-f363CVE-2021-3321zephyrproject-rtoszephyr+1EPSS score0.76%
Integer Underflow in Zephyr in IEEE 802154 Fragment Reassembly Header Removal. Zephyr versions >= >=2.4.0 contain Integer Overflow to Buffer Overflow (CWE-680). For more information, see https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-w44j-66g7-xw99